ZZ

ZZ

ZZ is a speedsolving method invented by Zbigniew Zborowski in 2006. Its key idea is to orient every edge first. After that, the whole first two layers can be solved turning only R, U and L, with no cube rotations and no F or B moves. The last layer then has no flipped edges, which cuts its case count a lot.

Compared with CFOP: you spend more thinking during inspection, but F2L turns smoothly and you never see an OLL with flipped edges.

Steps

The pictures are unfolded cubes (yellow on top, green in front). Coloured stickers are solved pieces; grey ones aren't solved yet.

  1. EOLine: orient all 12 edges and place the DF and DB edges, so a line runs across the bottom. (Pieces are named by the faces they touch: DF is the edge between Down and Front, the white-green edge; DB is between Down and Back, the white-blue edge.) It takes about 6 moves on average and at most 9.

    • EOCross is the modern alternative: orient the edges and solve the whole cross. It's harder to plan in inspection but makes F2L easier. Most fast ZZ solvers use it now.

  2. ZZF2L: build the left 1x2x3 block, then the right one, turning only R U L. With EOCross this is plain pair-by-pair F2L, still <R, U, L> only.

    Left block Both blocks (F2L done)
  3. Last layer: every edge is already oriented, so the top always shows a yellow cross. Only corners and permutation are left (see the options below).

    This example is solved by Sune, then T perm.

Edge orientation

An edge is good when it can be solved with R L U D turns alone, and bad when it needs an F or B quarter turn. Bad edges always come in an even number: 0, 2, 4, … 12.

To check an edge, hold the cube with F and B fixed and look at its sticker on the U/D face. For an edge in the middle layer, look at its F/B sticker instead.

In this scramble, the dots mark the 6 bad edges (each edge has a dot on both of its stickers):

Scramble: R2 D' F U2 L' B R' U F' D2 L U' B2 R

To fix bad edges, bring them to the F or B face and turn that face a quarter turn (F, F', B or B'). Each quarter turn flips the 4 edges on that face. Typical cases:

Because a quarter turn flips good edges to bad too, with k bad edges on F, doing F changes the bad count by 4 - 2k. With k = 2 nothing improves. Move edges onto F with U, D, R, L turns (these never change orientation):

Last layer options

Because edges are oriented, the last layer is a subset of the CFOP last layer:

Option Steps Algorithms Notes
OCLL + 2-Look PLL 3 7 + 6 Beginner. 2-Look OLL without the edge step, then 2-Look PLL
OCLL + PLL 2 7 + 21 Same as CFOP's full PLL step; OLL is only its 7 corner cases (OLL 21 to 27)
COLL + EPLL 2 42 + 4 Solve corners fully, then one of 4 edge cycles (Ua, Ub, H, Z)
ZBLL 1 472 One look for the whole last layer: PLL is part of it, 493 cases in all
Winter Variation + PLL 1 + 1 27 + 21 Orient corners while inserting the last pair (when it inserts as R U R')

The 7 OCLL cases are already in this vault, in the 2-Look OLL table: Sune, Antisune, H, Pi, U, T and L. EPLL is the edge step of 2-Look PLL: Ua, Ub, H and Z.

Suggested learning path

  1. EOLine, then the blocks, until you can plan EOLine in the 15 seconds of inspection.
  2. Last layer: OCLL + 2-Look PLL. You already know these from CFOP.
  3. Full PLL, so the last layer takes 2 looks.
  4. Switch EOLine to EOCross.
  5. COLL + EPLL, then ZBLL subsets one at a time (T, U, L, then H, Pi, Sune, Antisune).

Pros and cons

Pros

Cons